江淮叉車電瓶--江淮叉車電瓶廠家江淮叉車電瓶--江淮叉車電瓶廠家、江淮叉車電瓶--江淮叉車電瓶廠家

我公司銷售國內外各大品牌叉車專用蓄電池，日本GS、火炬、荷貝克、霍克  等等！

廠家直接拿貨，價格優勢明顯，質量保證3年！歡迎全國客戶前來訂購！

地區偏遠地區運費可與我公司銷售經理聯系：  13718107657  孫經理

北京凱力威科技有限公司，是一家集服務與銷售一體化的蓄電池公司，發展的過程中,不斷與國內多個電池科研機構交流合作，設計生產，規模不斷擴大，是目前廣東省同行業銷售量多、規格齊全、價格優惠的性蓄電池企業！ 我們的任務是積極尋找新產品，逐漸淘汰現有質量差的電池品牌；努力開發新市場和潛質好的分銷商，全力打造健全、高效的分銷網絡；利用現有資源，加大宣傳力度，捕捉潛在客戶信息，逐步建立客戶數據庫，開展數據庫營銷，從而拉動終端銷售；健全、統一的的售后服務管理系統，為分銷商解決后顧之憂。 主 營：統一蓄電池，風帆蓄電池，駱駝蓄電池，長青蓄電池，穗航蓄電池，建航蓄電池，海鷗蓄電池，豐田叉車蓄電池，電動叉車蓄電池，合力叉車蓄電池，ups蓄電池，免維護蓄電池，船檢免維護蓄電池，船用發電機蓄電池，高爾夫球車蓄電池，汽車免維護蓄電池，大宇叉車蓄電池，電瓶車蓄電池，應急燈蓄電池，現代叉車蓄電池，林德叉車蓄電池，小松叉車蓄電池，杭叉叉車蓄電池，康明斯發電機蓄電池，新力叉車蓄電池，進口叉車蓄電池，臺勵福叉車蓄電池，廈叉叉車蓄電池，天力叉車蓄電池，大連叉車蓄電池，斗山叉車蓄電池，江淮叉車蓄電池，柳工叉車蓄電池，龍工叉車蓄電池，日本神鋼叉車蓄電池，安徽叉車蓄電池，力至優叉車蓄電池，天宇叉車蓄電池，臺州叉車蓄電池，濰柴發電機蓄電池，三菱叉車蓄電池，寶驪叉車蓄電池，吉鑫祥叉車蓄電池，揚州TCM叉車蓄電池，JAC叉車蓄電池，友高叉車蓄電池，美科斯叉車蓄電池，友佳叉車蓄電池，奧薩叉車蓄電池，大隆叉車蓄電池，靖江叉車蓄電池，玉柴叉車蓄電池，三一叉車蓄電池，依格曼叉車蓄電池，等。 公司從事電池行業十余年，積累了豐富的技術經驗，掌握手廠方資源，有著過硬的技術知識，真誠、熱情的售后服務，贏得眾多4S店，汽車修理廠，零售商，物流公司，搬家公司，國家企事業單位，政府部門等的支持和信賴，并保持友好的長期合作關系！ 在我們這里，您將買到適合你，同等質量，價格的電池，并為您提供熱情，周到的‘三包”服務,公司有自己的配送貨車，我們的技術人員將上門為您安裝服務。歡迎來電咨詢或訂貨！國內、省內、均可發運！ 我們的口號：尋一流產品，找一流的分銷商，做踏實的紐帶！

叉車蓄電池初充電

1.1 未經使用的叉車蓄電池在使用前應進行初充電。初充電前應將電池表面擦拭干凈，檢查有無損壞；按串聯方式組成電池組時應緊密無間隙，保證極性正確。螺栓連接時應壓緊螺栓保證連接可靠。

1.2 擰下液孔塞，清除塞內透氣孔上密封物保證透氣孔暢通；或拔下密封蓋換上掀蓋式液孔塞并打開掀蓋。

1.3 在充電設備能正常工作的條件下將密度為1.260±0.005（25℃）溫度小于30℃的 硫酸電解液灌入電池，液面高出保護板15～25（mm）或符合右圖要求。此時為了將低電解液因化學反應而上升的溫度讓電解液充分滲入極板，隔板孔隙內；電 池需靜置3～4小時，不超過8小時。待液溫降至35℃以下方可進行初充電。（必要時可在冷水槽中降溫）靜置后液面下降應補充電解液。

1.4 硫酸電解液是用符合國家標準gb4554-84的需電池硫酸與蒸餾水配制而成，切勿用工業硫酸、自來水代用。

1.5 擦干濺落在電池表面的電解液，將電池組的正、負極分別與直流電源的正、負端相接，接通電源；電源電壓應高于電池組串聯電壓的50%，依據電池額定容量十分 之一電流進行,第①階段電流充電，沖至電壓達到2.4（v）時改用第①階段電流減半進行第②階段電流繼續充電。充電過程中電解液溫度不得超過45℃，接近 45℃時應減半充電電流或暫停充電；待液溫降至35℃以上再繼續充電。但需適應延長充電時間。

1.6 充足電的一句：在第②階段充電至電壓達2.6（v），電壓變化不大于0.005（v）；電解液密度達到1.280±0.005（25℃），2小時內無明顯變化并有細密氣泡激烈發生時就認為電池已充足電。其充電電量為額定容量的4～5倍，充電時間約70小時。

1.7 為了準確控制電解液中硫酸含量，在充電末期應檢查各電池的電解液密度；如有不符則用蒸餾水或密度為1.40的硫酸進行調整，并應在充電狀態下的2小時內將電解液密度與液面調整至規定值。

1.8 初充電結束后將電池表面擦干凈，裝上液孔塞或閉上掀蓋式液孔塞的掀蓋，方可投入使用。

1.9 產品若是干式荷電蓄電池時，不需要進行初充電，使用前加電解液密度為1.270±0.005，加液后2小時，（***長不超過48小時）應經常充電中第二 階段充電電流的二分之一充電18小時后再用該電流量乘1.5繼續充電待單位電池電壓達到2.6v時充電結束，靜止1小時即可投入使用。

Electric forklift battery 48v450ah-24-9db450

According to gb10827-1999 "motor vehicle safety standards" the relevant provisions are as follows: "battery charging and replacement"

1, in order to charge or replace batteries before the vehicle must be correctly positioned and brake.

2, must be in charge when the exhaust cap to release gas and disperse heat cover to prevent the electrolyte from the correct position and keep open the battery compartment or the effective porosity.

3. Measures must be taken to prevent the fire spark or arc no smoking in the battery charging area.

4, tools or other metal items must be far away from the top of the battery is not stamped.

5, the upper part of the battery should be dry terminal should be kept clean and coated with a little vaseline and correct tightening.

6, re install the battery must be placed in the correct position of the battery.

7, prohibit the use of open flame to check the battery electrolyte level.

8. When the solution of the acid altar must be used, the acid altar tilting device or siphon dilution concentrated sulfuric acid is used to prepare the electrolyte, and only the concentrated sulfuric acid can be added into the water and the water is not allowed to be added into the concentrated sulfuric acid.

Several ways of charging forklift batteries

Battery charging of industrial electric vehicles usually have the following ways:

A, the vehicle will stop working, connect the charger to charge the battery;

B, the battery in the vehicle with the spreader, manual or automatic car battery replacement battery replacement system has been removed, changed into a fully charged battery.

The production and replacement of the gas of forklift battery in charging system

1.1, the battery charging process is generated by the gas mixture of hydrogen and oxygen gas (gas explosion). This gas is colorless, tasteless, odorless, acid mist but they are mixed together, so there is a pungent smell.

2.1, hydrogen gas is a highly explosive, if the hydrogen concentration of air is more than 3.8%, a fire will explode.

3.1, in order to prevent the explosion caused by the final stage of this charge, charging place to take full ventilation, no fireworks!

4.1, the battery will always stay inside the oxygen and hydrogen gas explosion of gas, so in the vicinity of the site should be strictly prohibited Fireworks (Ming Huo, sparks, static).

5.1 the temperature between the charging is not easy to be higher than 40 degrees Celsius, otherwise it will affect the electrolyte charging temperature is too high (the manufacturers to charge the battery when the temperature requirements of some differences, but the high temperature must be no good)

 Sichuan Changjiang truck Co., Ltd. was founded in 1999. Specializing in forklift truck sales, spare parts sales, forklift rental, with the old for new, repair and transformation of business. Long term overhaul, transformation of business, great exercise in Sichuan branch staff capacity, and accumulated a wealth of experience, and in the vast number of customers has won a good reputation. Co., Ltd. is the company is Anhui, China UnionPay Heavy Construction Machinery Co., Ltd. production of the JAC forklift truck set vehicle sales, parts, after-sales service, technical advice as one of the 4S model Sichuan branch. The sales company is located in Chengdu road three building No. 168 of No. 30 (Tel:57), the service station is located in the locomotive factory on the right side of the door 150 meters, the factory accessories to provide various types of forklift parts, so that the majority of customers, that is to solve all the problems of the company's main operating forklift! To diesel forklift, battery forklift and tractor electric stacker, forklift, manual forklift, secondhand forklift, forklift accessories, tools etc.. The company adhering to the "customer first, forge ahead" business philosophy, adhere to the "customer first" principle to provide our clients with quality services. Welcome customers patronage! Anhui Jianghuai yinlian heavy-duty engineering machinery Co. Ltd. (hereinafter referred to as the heavy industry), is a large domestic automobile group company, Anhui Jianghuai Automobile Group Co. Ltd. (hereinafter referred to as JAC..