美國BC U-2400電刀分析儀
型號：BC U-2400 類別： 質控儀器 品牌：美國BC pdf資料: 美國BC U-2400電刀分析儀.pdf
美國BC U-2400電刀分析儀詳細介紹：
美國BC
U-2400電刀分析儀是一種高，真實的RMS測量系統，用于電發生器的校準和常規性能驗證。它提供比以前可以使用傳統電單元分析儀
設計更高的準確度。U-2400提供的低電內部負載組，范圍為0至6400歐姆，單位為1歐姆。它是基于微處理器的，并且利用的硬件和軟件
的組合來提供準確的測試結果，甚至從“嘈雜”的U發生器波形，如“噴霧”。在U-2400中使用的待定DFA?技術允許系統對電發生
器產生的復雜RF波形進行大量數字化，
U-2400電刀分析儀
美國BC
U-2400電刀分析儀與許多傳統的U分析儀不同，U-2400具有內部HV設置繼電器來控制測量路徑，允許用戶在功率測量，泄漏測
量，CQM / RECQM / ARM測試之間切換，甚至運行可能包括任何或這些測試 - 甚至沒有移動的電線。
美國BC U-2400電刀分析儀內部的電流互感器檢測流過內部測試負載的RF電流，并產生由微處理器數字化和分析的比例電壓。使用電流互感器組合U-2400的標準和低范圍，用戶可以控制從類型的電發生器獲得高和高分辨率讀數的能力。
美國BC U-2400電刀分析儀主要功能：
? 使用DFA?技術的真值讀數
? 行業標準電流檢測技術
? mV，mV峰值，ma，波峰因數和功率（瓦數）范圍
? 帶觸摸屏的彩色QVGA顯示屏
? 讀數測量的1％
? 數字校準 -轉
? 可選的顯示選項
? 測量RF信號的圖形屏幕上表示
? 標準（1000毫伏）和低范圍（100毫伏）與自動縮放能力
? 通過某些電制造商提供的用于低工作周期脈沖輸出脈沖RF波形測量模式
The Model U-2400 Electrosurgical Unit yzer is a high-accuracy,
true RMS RF measurement system digned to be used in the calibration
and routine performance verification of Electrosurgical Generators. It
offers a higher degree of accuracy than previously attainable with
conventional Electrosurgical Unit yzer digns. The U-2400
provid an advanced low reactance internal load bank with a range of 0
to 6400 ohms in 1 ohm increments. It is microprocsor-based and
utiliz a combination of unique hardware and software to provide
accurate and reliable tt rults, even from “noisy” U Generator
waveforms such as “Spray”. The Patent Pending DFA? Technology utilized
in the U-2400 allows the system to aggrsively diize the complex
RF waveforms produced by Electrosurgical Generators, yze each
individual dial data point and provide highly accurate measurement
rults.
The U-2400, unlike many conventional U yzers, has internal HV
setup relays to control the measurement path, allowing the user to
switch between power measurements, leakage measurements, CQM/RECQM/ARM
tting or even run an autosequence that could include any or all of
the tts – without even moving wir around.
The current transformer internal to the U-2400 sens the RF current
flowing through the internal tt load and produc a ratiometric
voltage which is diized and yzed by the microprocsor. Combining
the standard and low rang of the U-2400 with the use of the current
transformer, the user has full control over the ability to get high
accuracy and high rolution readings from all t of Electrosurgical
Generators.
The following are some of the main featur:
? True RMS readings using DFA? technology
? Industry standard current sensing technology
? mV, mV peak, ma, crt factor and power (wattage) rang
? Color QVGA display with touchscreen
? 1% of reading measurement accuracy
? Dial calibration – no pots to turn
? Selectable display options
? Graphical on-screen reprentation of measured RF signal
? Standard (1000 mV) and low range (100 mV) with autoscaling capability
? Pulsed RF waveform measurement mode for low duty cycle pulsed outputs offered by some electrosurgical manufacturersSAG:
U-2400電刀分析儀,U-2400,美國BC U-2400電刀分析儀,BC U-2400
