一.電器性能規格 ELERICAL CHARAERISTICS |
| ||||
項目Item | 測試條件 Test Conditions | 表現 Performonce |
| ||
接觸電阻 Conta Resistance | 在微小電流(100mA )以下測試 Measured at all l current (100mA or less) 1000HZ | 30毫歐以下 30mΩ Min |
| ||
緣電阻 InsulationResistance | 輸入500V電壓1分鐘,按以下方式測試:Apply a voltage of 250V DC for 1 min to following portions after mhich measurement shall be made: (1) 塑膠體與針腳之間 (1)Between body and conduor (2) 不接觸的針腳之間 (2)Between conduor not to be conta |
100兆歐以上 100mΩ Min |
| ||
耐電壓 Dieleric Strength | 輸入AC500V(50-60HZ)電壓,1分鐘感應電流為0.5MA,按以下方法測試: AC 250V ims(50-60HZ) for 1 min trip current: 0.5 mA (1)塑膠體與排腳之間 (1)Between terminals (2)不接觸的排腳之間: (2)Between individual terminals and frame | 沒有緣破壞等異常 No damage to parts arcing , orbreakdown etc |
| ||
使用溫度范圍 Praical Temperature Range |
-25℃----+75℃ |
|
| ||
測試標準狀態 Standard Conditions Atmospheic
| 在沒有指定的情況下測試溫度,濕度,氣壓如下: Unless otherwise specified , the stardard range or atmospheric conditions for making measurements and tests are as follows (1) 溫度為5℃--35℃ (1)Ambient temperature:5℃to 35℃ (2) 濕度為45%--85% (2)Relative humidity :45% to 85% (3) 氣壓為80KPA----106KPA (3)Air pressure : 80Kpa to 106Kpa |
|
| ||
二.機械性能規格 MECHANICAL CHARAERISTICS |
| ||||
動作力 Operation Force |
| 250gf&plun;50gf 160gf&plun;20gf |
| ||
端子強度 Terminal Strength | 在排腳前端任意一個方向的先端加上300克力力度測試,時間為15秒 A static load of 300gf shall be applied to the tip of the terminal for 15 sec in any direion | 在排腳中沒有裂開,松動等異常滿足于機械,電器性能:.Elerical charaeristics shall be satisfied without damage or escessive looseness of terminals |
| ||
壽命測試 Life Test | 負荷:在負荷的條件下以每分鐘25-30回的頻率進行100,000次的負荷測試; Aswitch shall be subjeed to 100.000 cycles at a speed of 25-30 cycles for 1 min | 接觸電阻不能過100毫歐,Conta resistance shall be 100mΩMax其他滿足于機械,電器性能Mechanical and elerical charaeristics shall be satisfied |
| ||
|
|
|
| ||
| 三.耐久性 DURABILITY | ||||
| 項目Item | 測試條件 Test Conditions | 表現 Performonce | ||
| 可焊性試驗 Solderability Test | 溫度為245&plun;5℃,時間為3&plun;0.5秒 The solder bath of 255&plun;5℃for 3&plun;0.5 seconds | 焊錫部分粘錫均勻,飽滿,錫面平滑 Area of soldering need be ooth and good performance | ||
| 耐熱試驗 Heat Test | 放置在溫度85&plun;2℃中測試96小時后,再放置常溫中1小時來測定. The switch shall be stored at a temperature of 85&plun;2℃for96 hours, Then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made |
外觀無異常 ,能滿足于機械,電器性能 There shall be no defomation or cracks in molded part | ||
| 耐冷試驗 Cold Test | 放置在溫度-20&plun;3℃中測試96小時后,再放置常溫中1小時來測定. The switch shall be stored at a temperature of -20&plun;3℃for96 hours, Then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made | |||
| 潮濕試驗 Humidity Test | 放置在溫度40&plun;2℃相對濕度為90%-96%環境中96小時后,再放置常溫中1小時來測定. The switch shall be stored at a temperature of40&plun;2℃and a humidity of 90%-96% for 96 hours, Then the switch shall be maintained at standard atmospheric condition for 1 hour after which measurement shall be made | |||



